Hi all,
Who has the pro diffuser fitted ? Was this an easy upgrade? Can anyone share good pics of it fitted ?
Cheers
Sent from my iPhone using Tapatalk
Hi all,
Who has the pro diffuser fitted ? Was this an easy upgrade? Can anyone share good pics of it fitted ?
Cheers
Sent from my iPhone using Tapatalk
I had one fitted to my JCW and we fitted one to the wife’s 210 not long before we changed cars and the Challenge comes with it as standard. They are bonded onto the back bumper so once it’s on, it’s on
Racing Grey F56 JCW GP 0370 - Chilli Red Mirror Caps, Custom OHC Alcantara Steering Wheel, Motech Performance By PiperCross Panel Filter, Custom GP Steering Wheel Spoke, Custom GP Stitched Carbon Side Scuttles, JCW Pro Mats, RSI C6 Carbonfibre Scoop, JCW Pro Stitched Carbon Boot Handle
Ice Blue R55 Clubvan - JCW Shiftlight, JCW Carbon Fibe Handbrake, JCW Carbon Fibre Dash, JCW Steering Wheel, Recaro JCW Sportster CS, CoolerWorx ShortShifter, BC Racing Coilovers, JCW Brembo 4pots, HEL Braided Lines, JCW Front Bumper, MINI Challenge Splitter, White Rota Blitz
Cheers William, interesting about the bonding, I did see a section on the fitting guide about glueing but it didn’t look like it was too the bumper itself ! That may rule that enhancement out
Sent from my iPhone using Tapatalk
Ive got the pro diffuser fitted too but on this occasion I didn’t fit it. It was done by the garage so unfortunately I can’t help with the fitting side of things but interesting to hear it’s bonded on as I was planning on taking mine off and getting it painted
You only need two tools in life WD40 and Duct Tape. If it doesn't move and should use WD40 and if it moves and shouldn't use Duct Tape.
Anyone know how to release the various clips around the trim as shown in the pic below to remove the bumper insert ?
Sent from my iPhone using Tapatalk
They’ll just push out but they’ll be tight. You’ll probably need to start at one end and work your way to the other. If I mind right I used a flat end screwdriver to push the clip down and then tried to pull the trim out at the same time. Once you get the first few out the others will be easier. Probably a job for two if you can ...
Sent from my iPad using Tapatalk
You only need two tools in life WD40 and Duct Tape. If it doesn't move and should use WD40 and if it moves and shouldn't use Duct Tape.
Try will be the same as most other MINI clips a bit tight but once you get started they come away
Racing Grey F56 JCW GP 0370 - Chilli Red Mirror Caps, Custom OHC Alcantara Steering Wheel, Motech Performance By PiperCross Panel Filter, Custom GP Steering Wheel Spoke, Custom GP Stitched Carbon Side Scuttles, JCW Pro Mats, RSI C6 Carbonfibre Scoop, JCW Pro Stitched Carbon Boot Handle
Ice Blue R55 Clubvan - JCW Shiftlight, JCW Carbon Fibe Handbrake, JCW Carbon Fibre Dash, JCW Steering Wheel, Recaro JCW Sportster CS, CoolerWorx ShortShifter, BC Racing Coilovers, JCW Brembo 4pots, HEL Braided Lines, JCW Front Bumper, MINI Challenge Splitter, White Rota Blitz
I thought Audi trim was well secured I had a go at releasing them earlier along with the outer edge trim but couldn’t get them to budge, did you do the job with the bumper in situ ?
Sent from my iPhone using Tapatalk